MSD Tech Support Forums

Go Back   MSD Tech Support Forums > MSD Ignition Forums > Trouble-Shooting

Trouble-Shooting Diagnose your ignition

Reply
 
Thread Tools
  #1  
Old 10-05-2012, 09:43 AM
shelbyCSX6000 shelbyCSX6000 is offline
Junior Member
 
Join Date: Oct 2012
Posts: 3
Default Shelby CSX6000 with MSD 8595/blaster 3

Firstly let me apologize for the lengthy post but I have some issues I am hoping you can guide me thru for a cure.
My car (Shelby CSX 6000 S/C, Shelby 427 engine) had always run perfectly until last July 2011 when it would not start cold, 700 miles on car. After some diagnostic work on my part I determined it to be a ignition issue. No spark. I called Shelby engine and they sent me a new MSD distributor identical to what was in it, a MSD 8595. I installed the distributor and it has run perfectly, until last week that is when it did the something, no start after cooled down. This time it has 1399 miles. I figured that the first distributor could have been a bad one but now the odds of getting two bad ones would be astronomical. I am looking for a other cause, leading to the failure of them before I put a new one in again. This time I have to purchase it, $400.00. I have purchased a new MSD Blaster 3 coil also just to be certain, which is also what it came with from Shelby.

I have had several lengthy conversations with MSD about this and have turn several test as they requested.
Having run a ground test, 0 ohms from NEG post of battery to engine block and engine running test, 13.58 volts at battery and coil positive to block, ground wire from battery to frame to engine.

Even thought the distributor and coil are not longer under warranty, even though they have little use, I hope to avoid getting stranded and paying tow bills, flat bed as it were. I am so uncertain about this ignition setup that I have ordered a car hauler trailer which was easer than trying to find someone to haul a $140,000 car. Further I am returning the latest MSD failed distributor for repair and hopefully diagnosis. I figure I can carry a spare distributor in the trunk. Maybe I should switch to something else? Thanks, R.A.Conner
Reply With Quote
  #2  
Old 10-05-2012, 10:03 AM
msdtech1955's Avatar
msdtech1955 msdtech1955 is offline
Senior Member
 
Join Date: Jan 2008
Posts: 8,383
Default

mr conner , i believe one of the techs talk to you this morning about the
this....
what is the rma number?
Reply With Quote
  #3  
Old 10-05-2012, 05:23 PM
shelbyCSX6000 shelbyCSX6000 is offline
Junior Member
 
Join Date: Oct 2012
Posts: 3
Default

R1227900000

Last edited by shelbyCSX6000; 10-06-2012 at 05:06 AM. Reason: RMS number
Reply With Quote
  #4  
Old 10-06-2012, 04:56 AM
shelbyCSX6000 shelbyCSX6000 is offline
Junior Member
 
Join Date: Oct 2012
Posts: 3
Default Csx6000

Once I receive it back Ill send the other one I have and see if the same thing happen to both, Thanks! Richard

Last edited by shelbyCSX6000; 10-06-2012 at 05:06 AM. Reason: spelling
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 08:59 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
2011 MSD Performance