MSD Tech Support Forums

Go Back   MSD Tech Support Forums > Nitrous Diagram Help

Nitrous Diagram Help Collection of Nitrous diagrams for different setups.

Reply
 
Thread Tools
  #1  
Old 07-12-2011, 09:44 AM
msdtech1955's Avatar
msdtech1955 msdtech1955 is offline
Senior Member
 
Join Date: Jan 2008
Posts: 8,915
Default custom drawings

first post .... if your looking for some help with a drawing in a nitrous application (digi-set-relays-retards) ..this would be the place... dont be afraid to ask .


i'll start off with this normal one.
2_step_nitrous_latching_relay 7531.JPG
Reply With Quote
  #2  
Old 08-23-2011, 09:18 AM
msdtech1955's Avatar
msdtech1955 msdtech1955 is offline
Senior Member
 
Join Date: Jan 2008
Posts: 8,915
Default another custom drawing link.

http://www.msdignition.com/StarterAp...aspx?wiki=1283
Reply With Quote
  #3  
Old 01-29-2012, 06:51 PM
JMillerJr76 JMillerJr76 is offline
Junior Member
 
Join Date: Jan 2012
Posts: 10
Default

What diagram would be the best for my application, Im running a single stage plate and a bang button, 6al box, transbrake, and now a 8975 timing controler. What would be a good diagram to wire it so that when im on the trans brake, the motor is still at full timing, and the solenoids are disabled, and when I release the trans brake, it pulls timing, and enables the nitrous . I know it will end up going through relays, and I have them, just need a little info. Thanks fellas
Reply With Quote
  #4  
Old 01-30-2012, 07:33 AM
msdtech1955's Avatar
msdtech1955 msdtech1955 is offline
Senior Member
 
Join Date: Jan 2008
Posts: 8,915
Default

do you wish to use timers?
Reply With Quote
  #5  
Old 01-30-2012, 03:21 PM
JMillerJr76 JMillerJr76 is offline
Junior Member
 
Join Date: Jan 2012
Posts: 10
Default

No, I won't be using timers at this moment. I'm figuring I will be using the first 3 stages to pull the amount of timing that I need. I think I will set the engine at 34* and pull anywhere from 10 to 12*. Thanks again!!
Reply With Quote
  #6  
Old 01-31-2012, 08:29 AM
msdtech1955's Avatar
msdtech1955 msdtech1955 is offline
Senior Member
 
Join Date: Jan 2008
Posts: 8,915
Default

drawing it up right now... also p/m me your email address ...so you can see it bigger
Reply With Quote
  #7  
Old 01-31-2012, 01:12 PM
msdtech1955's Avatar
msdtech1955 msdtech1955 is offline
Senior Member
 
Join Date: Jan 2008
Posts: 8,915
Default

here ya go.
6al 8975 2 step n20 launch 2 step (2).jpg
Reply With Quote
  #8  
Old 01-31-2012, 02:02 PM
JMillerJr76 JMillerJr76 is offline
Junior Member
 
Join Date: Jan 2012
Posts: 10
Default

Pm sent
Reply With Quote
  #9  
Old 03-01-2012, 10:46 AM
cj ford cj ford is offline
Junior Member
 
Join Date: Mar 2012
Posts: 3
Default

.................

Last edited by cj ford; 03-01-2012 at 07:09 PM. Reason: wrong section
Reply With Quote
  #10  
Old 03-11-2012, 07:06 PM
mcat mcat is offline
Junior Member
 
Join Date: Mar 2012
Posts: 13
Default

nitrous application can you draw this up? relays and all. i will be using heavy duty golf cart continuous duty (ford starter type) relays for my nos/ fuel solenoids and regular 30 amp for the trans brake .. i think
grid 7730
box7720
coil 8261
box 7751
and edelbrock 79100 progressive
WOT switch
i need a revlimiter while on the trans brake
i want full timing until transbrake is released then initial timing dump to 11-15 total from 34-36 then i want to be able to map the timing with the grid.
i think thats what i want what do you think?
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 11:48 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
2011 MSD Performance